LED round tail light with Oi flash controller and black mounting bracket
Modulation brake light effects are great for grabbing the attention of somebody behind you who might be distracted. Package includes an Oi flash controller, a LED taillight, a black mounting bracket.
Sealed LED module with IP66 dust & waterproof compliant.
→ What does IP66 waterproof rating mean? IP6x is the highest dust resistance rating, so this product is fully protected against dust.
IPx6, the third-highest water resistance rating, means this product can withstand powerful water jets up to 3 mins from a distance of 3 meters, tested in laboratory conditions.
Code | Effective against | Description |
---|---|---|
6 | Dust tight | No ingress of dust; complete protection against contact (dust tight). A vacuum must be applied. Test duration of up to 8 hours based on air flow. |
Code | Protection against | Test duration | Description |
---|---|---|---|
6 | Powerful water jets | 3 mins from a distance of 3 meters | Protection from water projected in powerful jets from a nozzle with a 12.5mm diameter opening in any direction |
- Feature
- Get more attention and visibility from the vehicle behind you in traffic.
- 16 flashing modes that no one else has.
- Much brighter and cooler than a normal taillight.
- 12 LEDs for stop/ tail lamp.
- IP66 dust & waterproof compliant*.
- Indicator function. (Need to install two lamps)
- Pre-cut plate for round LED tail light.
- Chromed finish for rust-resistance.
- Mounting bracket and nuts included.
- Oi Flash Controller SPEC
♦ 16 different modes that can be applied to your stop light, turn signal light, hazard light, and decoration light.
♦ Operate in the voltage range from 6.5V to 16V. (Suitable for 12V vehicle power system)
♦ Ambient temperature must not below -20° (-4°F) and not exceed +85° (185°F).
♦ Works both for halogen & LED bulbs.
♦ Super-duper easy set up for LED lights. NO LOAD RESISTOR IS NEEDED.
♦ Maximum current rating up to 8A. (Suitable for up to 4 light bulbs with 21W)Oi Flash Controller is designed to replace a 3-pin flasher relay ONLY (not for a 4 or 5 pin relay, it will destroy the device).
- Material
Lens: Acrylic
Reflector, Frame: ABS
Bracket: Steel - Net Weight
309g - Package
LED tail light x 1, light mounting bracket x 1, Hex nut x 2, Oi flash controller x 1
- Color
Tail/ stop: red LED
Indicator: amber LED
Bracket: chrome - Shape
Round - Light Source
Tail/ stop: 12pcs red LED, 12V 0.1W/ 12V 1.7W
Indicator: 6pcs amber LED, 12V 2.0W
The turn signal lights are 2.0W instead of 1.2W in mass production.
(Note: The imprint on unit wasn't revised specifically.) - Wire Length
Tail light: 145mm/ 5.7 inch
Oi flash controller: 155mm/ 6.1 inch - Type
Tail lamp, (optional)turn signal - Certification
EMI class 3 and IP66 dust & waterproof Compliant*
ECE, SAE approved.
2. Modification maybe needed during installation.
3. The finish of bracket is not intended to withstand heat and binding. It is merely plated to protect the steel for rust-resistance. After tweaking the bracket to fit your fender, we suggest polishing and chroming, or at least a good coat of spray paint.
4. Newer Harley-Davidsons run the "indicator flash rate" through the OEM TSM/TSSM modules. You can not use Oi flash controller if the OEM TSM/TSSM modules include the circuit of your motorcycle.
*Please allow measuring deviation due to manual measurement.
There are yet no reviews for this product.
Please log in to write a review. Log in